Sponge and Fabric Laminator

1.Practical laminator 2.Hand wheel control or pneumatic control is optional 3.High quality with saving cost

This laminator mainly used in :

1.Gluing and pasting of foam, fabric, PVC, EVA etc,

2.Also adhesive-bonded the raw material of shoemaking, making cap, handbag, box, sofa automobile seating cushion etc.

Characteristics:

1.Pressed by heat-proof ventilate mesh to add adhering strength.

2.Improve the product quality greatly and save cost.

3.For clamp roller, both hand wheel adjustment and the pneumatic control are available.

4.Surface of heating roller is coated with Teflon in order to  efficacious prevent the hot melt adhesive against sticking on the surface of roller and carbonization

5.It equipped with speed regulation system VVVF control, and automatic temperature control system; it also can measure the length, easy to control production output and product quality.

6.Spreading width can be momentarily designed according to the clients requirement to control the cementing amount,diameter of heating roller is optional

7. Adjust the speed of heating roller according to the working requirement,both colloid trough and heating roller can control temperature independently.

8. New design structure, reliable technology, easy operation, low breakdown rate, long service time.

9. High-efficiency cooling device insure the application range of the basic materials 

Main parameter:

Type	01C
Size(L×W×H)(mm)	7800*2300*2400
Power	35KW
Motive Power	3HP+2HP(Computer VVVF control)
Standard for Heated Roller	Φ1200*1830 mm (optional)
Working Width	1830 mm (72'')
Work Speed	0-45y/min

Range of application

This laminator is siutable for producting  as following:

1. Shoe making materials, such as EVA with fabric, foam with fabric, fabric with leather, fabric with fabric, fabric with PE film, etc.

2. Clothmaking materials, handbag, such as fabric with waterproof film, fabric with fabric, fabric with fur, etc

Caution for using YA-01C Horizontal Net Belt Lamintor

1. The machine surface should be without watermarks, oil, dust, debris, large drum, mesh belt, rolling wheels, idler pulley, plastic pots, plastic roller, pulp wheel, knife plate should wipe, wash clean.

2. Strictly prohibited on-load open, barrier gate.

3. Motor can never exceed the load (110%); accelerate, deceleration turning "speed adjustment" knob should be careful, and gradually transferred to the required speed, or easily damaged motor.

4. Forbid to operate "positive inversion switch" when machinery is in running, otherwise fragile to damage converter and motor.

5. To adjust the wheel of stepless variable speed machine can fine-tune the tightness of gluing when machine running, keep material speed synchronous with the heating roller, but prohibit to rotate the hand wheel when machine stop, (that is to say can not change speed), Otherwise, easy to damage stepless gearbox.

6. Keep waxing regularly on stepless gearbox, motor belts, often add oil in chains, bearings, cylinder stroke, and change oil regularly in worm gear reducer to ensure its lubrication, running well.

7. Under normal circumstances, "Manual / Auto" switch of electrical panel box should be at "automatic" position, electric eyes, limit switch works, or else mesh belt does not adjust automatically lead to run out the roller (accompanied by alarm sound continuously), in this case, stop as soon as possible, and re-adjust the location of mesh belt.

8. Mesh belt adjusted edge automatically only when the main engine in the "Forward" situation.

9. When work stopped, if the temperature table shows heated roller temperature above 80 degrees, it is prohibited strictly to stop running big rollers, or else damage mesh belt due to high temperature, it at your own risk, our company is not listed income within the scope of the warranty. Therefore, must let the mesh belt (big drum) keep running until the temperature below 80 degrees table showed, then stop. Out of work, the rubber roller are not allowed to pressure on the heated wheel, free state must be left vacant place.

10. Handle scraper board carefully, otherwise easy to damage the gluing embossing roller.

11. Big electric box should open regularly t check the time relay and intermediate relay whether loose or not, inside dust, cotton and other dirty (miscellaneous) material to be removed regularly to prevent blockage of cooling channel converter inconvenience of the machine.

12. Inverters data has been set well before leaving the factory, non-professionals is strictly prohibited to change, set, disassembly and repair.

Sponge and Fabric Laminator